WALLMIX SR-5 plaster is intended for decorative furnish inside and outside of buildings of concrete, brick plastered bases, and also application at the device of systems of thermal insulation of facades for the purpose of receiving various “bark” textures. Recommended for surfaces that require good vapor permeability and water-repellent properties.
Water-polymer latex dispersion with mineral fillers and modifying additives.
Carried out in accordance with the requirements of DSTU-N B A.3.1-23: 2013 and DSTU-N B B.2.6212: 2016. The base must be dry, strong and free of dust, dirt, oil, grease, wax and paint residue. Fragile layers need to be removed. Potholes, chips, cracks must be closed with a repair mixture. Strongly absorbing bases before performance of works it is necessary to process a first coat acrylic universal Wallmix Universal and to maintain from 4 to 6 hours, then to process a first coat acrylic WALLMIX Quarz-Primer, tinted under plaster color. Weak-absorbing and smooth bases before the beginning of work to process priming paint acrylic WALLMIX Quarz-Primer, tinted under color of plaster and to maintain from 4 to 6 hours.
When performing works it is necessary to comply with the requirements of current regulations. Mix the contents of the container thoroughly with a drill at low speed. Plaster is applied to the base with a stainless steel grater, which is held at an angle of 60 degrees to the surface. When the mixture stops sticking to the tool (5 – 15 minutes), plasters give the invoice by means of a plastic grater. When performing work on the formation of the texture, the tool must be kept parallel to the surface. Work on one surface should be performed continuously, following the rule of “wet on wet”, not allowing the worn layers to dry before applying the next layers. In case of a break in work to stick a painting tape along a line where it is planned to finish work, to put plaster with a call on a painting tape and to give it the desirable structure. Then remove the masking tape immediately along with the remnants of fresh plaster.
Do not add other components to the mixture.
Decorative plaster is made on the basis of natural stone, so the composition may include inclusions of dark crumbs, or crumbs of a flattened shape. Too careful application of the texture with a grater can lead to the removal of pigment from the surface of the crumb on the light-colored plaster. For color identity on the facade, it is recommended to use products of one batch.
The work should be performed at a temperature of +5 ° C to +30 ° C. The most effective result is achieved at a temperature of +20 ° C and a relative humidity of 60%. In other conditions, the operating parameters of the mixture may change. When performing works, the facade must be protected from direct sunlight, as well as high humidity (rain, fog, etc.).
The consumption of the mixture is: ~ 2.6 kg / m2 with a grain size of 2.0 mm; ~ 3.1 kg / m2 with a grain size of 2.5 mm.
In case of contact with eye mixture, rinse immediately with running water and seek medical advice.
The mixture must be stored in branded airtight packaging in a dry place, on pallets. Shelf life 12 months from the date of manufacture indicated on the package. Use damaged bags first.
Plastic buckets of 25 kg.
The manufacturer is not responsible for improper use of the material, as well as its use for other purposes and conditions not provided for in the technical description.
Density 1.8 kg /L Grain size 2.0mm, 2.5mm
Mixture proportion ~ 2.6 kg / m2, ~ 3.1 kg / m2
The time of formation of the surface film in 15 minutes
Acquisition of resistance to precipitation min 24 years
Adhesion to the base min 0.5 MPa
Vapor permeability min 0.05 mg / (m ∙ year ∙ Pa)
Base temperature from +5 ° C to +30 ° C
Operating temperature from -30 ° C to + 70 ° C
Due the constant optimization of the mixtures, please refer to the technical description on the manufacturer’s website. From the moment the latest version of the technical description, all previous ones become invalid.
STORE IN A DRY PLACE!
MIXTURE by TM “WALLMIX” ” 1.P.FS DSTU B B.2.7-233: 2010.
Production address: st. Magnitogorskaya, 1, Kiev, 02094, Ukraine