WallmixАR5 plaster is intended for decorative finishing inside and outside buildings of concrete, brick plastered bases, as well as for use in the installation of facade thermal insulation systems in order to obtain various “bark beetle” textures. Not recommended for use on a building plinth.
Water-polymer latex dispersion with mineral fillers and modifying additives.
Conducted in accordance with the requirements of DSTU-N B A.3.1-23: 2013 and DSTU-N B V.2.6-212: 2016. The base must be dry, durable and free of dust, dirt, oils, grease, wax and paint residues … Weak layers must be removed. Potholes, chips, cracks must be repaired with a repair mixture. Highly absorbent substrates must be primed with Wallmix Universal acrylic and kept for 4 to 6 hours, then treated with Wallmix quartz acrylic primer tinted to match the plaster color. Weakly absorbent and smooth surfaces should be treated with Wallmix-quartz acrylic primer, tinted to match the plaster color, before starting work and let stand for 4 to 6 hours.
When performing work, it is necessary to comply with the requirements of the current regulatory documentation. Stir the contents of the container thoroughly with a drill at low speed. The plaster is applied to the substrate with a stainless steel float held at a 60 degree angle to the surface. When the mortar stops sticking to the tool (5 – 15 minutes), texture the plaster with a plastic float. When performing work on the formation of the texture, the tool must be kept parallel to the surface. Work on one surface should be performed continuously, adhering to the “wet on wet” rule, not allowing the rubbed layers to dry out before applying the next layers. In the event of a break in work, glue the masking tape along the line where the work is planned to be completed, apply the plaster with an approach to the masking tape and give it the desired texture. Then immediately remove the masking tape along with the remnants of fresh plaster.
Do not add other components to the mixture.
Decorative plaster is made on the basis of natural stone, so the composition may contain inclusions of dark crumbs, or flaky crumbs. Too careful rendering of texture with a float can lead to the removal of pigment from the surface of the crumb on light-colored plaster. For color identity on the facade, it is recommended to use products of the same batch.
The work should be performed at a temperature of +5 ° C to +30 ° C. The most effective result is achieved at a temperature of +20 ° C and a relative humidity of 60%. In other conditions, the operating parameters of the mixture may change. When performing works, the facade must be protected from direct sunlight, as well as high humidity (rain, fog, etc.).
The consumption of the mixture is: ~ 2.6 kg / m² at a grain size of 2.0 mm; and ~ 3.1 kg / m² at a grain size of 2.5 mm.
In case of contact with eyes, rinse immediately with running water and consult a doctor.
The mixture must be stored in branded airtight packaging in a dry place, on pallets. Shelf life 12 months from the date of manufacture indicated on the package. Use damaged bags first.
Paper bags with an inner plastic layer of 25 kg.
The manufacturer is not responsible for improper use of the material, as well as its use for other purposes and conditions not provided for in the technical description.
The manufacturer is not responsible for the misuse of the material, as well as its use for other purposes and conditions not provided for in the technical description.
Density 1.8 kg / l Grain size 2.0mm, 2.5mm
Mixture consumption ~ 2.6 kg / m2, ~ 3.1 kg / m2
Skin formation time in 15 minutes
Acquisition of resistance to the influence of rainfall min 24 hours
Substrate adhesion min 0.5 MPa
Vapor permeability min 0.03 mg / (m ∙ hour ∙ Pa)
Base temperature from +5 ° C to +30 ° C
Operating temperature from -30 ° C to +70 ° C
Due the constant optimization of the mixtures, please refer to the technical description on the manufacturer’s website. From the moment the latest version of the technical description, all previous ones become invalid.
STORE IN A DRY PLACE!
MIXTURE by TM “WALLMIX” 1.P.FS DSTU B V.2.7-233: 2010.
Production address: st. Magnitogorskaya, 1, Kiev, 02094, Ukraine