Easy-leveling mortar WALLMIX D-35 is intended for the installation and repair of floor screeds on a rigid, non-deformable base (concrete, cementsand screeds, etc.) inside and outside buildings in civil and industrial construction under moderate and significant loads, except for traffic loads on caterpillar tracks, before applying self-leveling mixtures, laying tiles, parquet, linoleum and other coatings. When installing an easy-leveling screed on separating layers or on deformable bases (hydro, heat, sound insulation), the minimum layer thickness should be at least 40 mm. Can be used in underfloor heating systems. The recommended layer thickness is from 10 to 60 mm.
A mixture of cement with mineral fillers, reinforcing fibers and modifying additives.
Conducted in accordance with the requirements of DSTU-N B A.3.1-23: 2013, SNiP 2.03.13-88 and base must be dry, solid and cleaned of dust, dirt, oils, grease, wax and paint. Weak layers must be removed. Existing cracks must be widened and mechanically deepened to a depth of 1/2 of the top layer thickness and up to 5 mm wide, treated with WALLMIX UNIVERSAL deep-penetrating primer, held for 4 hours and covered with WALLMIX D-35 mortar mixture. The concrete base must be solid and at least 3 months old. The required brand strength of the base on which the screed will be laid must be at least 35 MPa. Highly absorbent substrates must be treated with WALLMIX UNIVERSAL deep-penetrating primer before work and cured for 4 hours. Weakly absorbent and smooth surfaces are treated with WALLMIX BETONCONTACT adhesive primer before starting work and kept for 4 to 6 hours.
Pour the dry mixture into a container with clean water at room temperature in a proportion of 0.14-0.25 l per 1 kg of the mixture (3.5-3.75 l per 25 kg bag). Stir thoroughly with a mixer or a low-speed drill with a nozzle until a homogeneous consistency without lumps and clots is achieved. Then let the solution stand for 5 minutes and mix thoroughly again. The resulting solution must be used within 1 hour.
Do not add other components to the mixture.
When performing work, it is necessary to comply with the requirements of the current regulatory documentation. The mortar mixture is placed between the preinstalled beacons. After laying the mixture, it should be evenly distributed and leveled using a rule-rail, a trowel or other tool. Final leveling and smoothing should be done with a plastic / styrofoam float or other tool. On an area of more than 20 m2, shrinkage joints must be made to prevent mechanical deformation. When installing a floor with a water heating system, it is necessary to fill the heating elements with water at room temperature and do not drain until they are fully set, and the layer thickness must be at least 25 mm above the upper edge of the heating pipes. The thickness of the layer of the WALLMIX D-35 mortar mixture applied in one pass should be from 10 to 60 mm. When applying a layer with a thickness of 60-100 mm, use the WALLMIX D-35 mixture with the addition of a coarse (up to 10 mm) filler (crushed stone, expanded clay etc.). Under normal climatic conditions (temperature +20 ° С and relative air humidity 60%), technological movement on the surface is possible after 6 hours. The solution layer must be protected from rapid drying and, if necessary, moistened by spraying. Ceramic tiles can be laid after 24 hours, other materials can be installed after 72 hours. Painting is allowed only after 7 days.
Work should be performed at temperatures from +5 ° C to +30 ° C. At the beginning of the work, for at least 48 hours, the solution must be protected from direct sunlight, as well as high humidity (rain, fog, etc.).
The consumption of the mixture is ~ 1.8 kg / m2 at a layer thickness of 1 mm.
The mixture contains cement, which causes an alkaline reaction at the time of hydration; during the job execution it is necessary to protect the eyes and skin. In case of contact with the mixture, rinse immediately with running water and consult a doctor.
The mixture must be stored in original sealed packaging in a dry place on pallets. The shelf life is 12 months from the date of production indicated on the package. Use damaged bags first.
25 kg paper bags with an inner polyethylene layer.
The manufacturer is not responsible for the misuse of the material, as well as its use for other purposes and conditions not provided for in the technical description.
Mixing proportion 0.14-0.15 L water/kg
Layer thickness 10-60 mm
Mix consumption per 1 mm of continuous layer ~ 1.8 kg /m²
The time of the mixture’s suitability for use 1 hour
Ready for initial loads min 6 hours
Compressive strength min 35 MPa
Flexural tensile strength min 6.0 MPa
Adhesion to the substrate min 0.5 MPa
Shrinkage max 1.3 mm/m
Frost resistance min 75 cycles
Base temperature from +5 ° С to +30 ° С
Operating temperature from -30 ° С to +70 ° С
In connection with the constant optimization of the mixtures, please refer to the technical description on the manufacturer’s website. From the moment the latest version of the technical description, all previous ones become invalid.
STORE IN A DRY PLACE!
MIXTURE by TM “WALLMIX” C.1.ST3 DSTU B V.2.7-126: 2011.
Production address: st. Magnitogorskaya, 1, Kiev, 02094, Ukraine.